Getting Familiar with Plumbing: Before Installing a Bathtub
Getting Familiar with Plumbing: Before Installing a Bathtub
Blog Article
How do you actually feel with regards to A Step-by-Step Guide to Installing a Bathtub?
Installing a tub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and also often, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably difficult task. If the old tub is readily accessible, the job can relocate immediately; if you have to open a wall surface to get rid of the old bathtub and place the brand-new bathtub, the job is much harder. In either instance, the job is within a house handyman's abilities, although you will require an assistant to vacate the old tub and also set in the new one. Ensure you have actually certified yourself for the work and fit attempting it. Rather than employing a contractor to take over a halfway-completed project, it is far better to think about utilizing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This post will certainly assist you set up a brand-new bathtub in your washroom if you have currently gotten a brand-new bathtub and don't require to transform the setup of your previous water supply pipes.
Your devices and also product list need to make up the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, then the first thing you must do is disconnect the water supply. After doing so, turn on the taps to drain any kind of water staying in the system. The process of eliminating the existing taps can be quite problematic as a result of the restricted access that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Before proceeding to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin ensuring that the washers are in area in between the tap as well as the sink. Secure the tap in position with the supplier supplied backnut. As soon as the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet connectors. The previous kind ought to be connected to the tap ends first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Using both wood boards under its feet, put the tub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the tub till the spirit level reviews degree.
To mount faucets, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Turn on the water system and inspect all joints and also new pipework for leaks and also tighten them if required. Load the tub as well as likewise examine the overflow electrical outlet as well as the regular outlet for leaks.
Finally, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at the very least once as this will certainly settle it into its final placement.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom ought to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to crack a rigid seal, creating the water to pass through the wall surface in between the bath and the tiling, resulting in issues with moisture and possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, and also can securing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealer can break rather very early if you do not take into consideration this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily available on the market. It is advisable to fit the tiles using waterproof or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that excerpt was beneficial. Are you aware of another person who is enthusiastic about the niche? Why not promote it. I love reading our article about A Step-by-Step Guide to Installing a Bathtub.
Avoid disaster, Call us! Report this page